13 Ekim 2008

*Motorcycle Terms Glossary (Motosiklet Terimleri Sözlüğü)


AC
alternating current (output from the alternator is AC)

AC welding
arc welding welding method which uses alternating current to provide heat for melting and fusion of metal parts.

accelerator pump
a small pump that squirts fuel into throat of carburetor as throttle is opened.

accessory system
part of electrical system consisting of lights, horn, electrical starter, turn signals, and warning systems.

additives
chemical compounds used to alter characteristics of lubricating oils and fuels.

air box
plastic, fibreglass or metal box mounted between carburetor and air filter. This box provides a volume of still, filtered air for induction into the engine.

air cooling
use of fins to dissipate heat from part into air.

air filter
a device with paper, oiled foam, oiled gauze or wire mesh to prevent entry of dirt or foreign particles into engine through air intake.

air-fuel mixture
finely atomized mist of air and fuel necessary for combustion. This mixture consists of approximately 15 parts air to 1 part fuel (15:1) at cruising speeds.


alternating current
(AC) electrical current which constantly reverses direction and polarity.

alternator
a crankshaft driven electrical generator that produces alternating current which must be rectified to DC current.

ammeter
an instrument for measuring current flow in electrical circuits.

ampere
(amp) electrical unit used to measure flow.

arc welding
a type of welding which uses an electric arc to produce necessary heat. Melting of base metal and welding rod to join two parts. Also known as electric-arc welding.

armature
portion of a DC generator housing generating coils.

asbestos
heat resistant material commonly used in brake and clutch lining. It is a known cancer causing substance if inhaled.

atomized
tiny particles of fuel mixed with air, making fine mist.

automatic transmission
a transmission not using a manually operated clutch.

backbone frame
frame which uses the engine as a structural member.

backlash
the clearance between meshed of two gears.

ball and ramp
a clutch release mechanism made of two stamped plates with three or four ramps. As one plate is rotated by clutch cable, balls climb ramps, forcing plates apart. This movement disengages clutch.

ball bearing
an antifriction bearing consisting of inner and outer races separated by hardened steel balls.

battery and coil ignition system
an ignition system with a battery as the source of primary ignition current.

battery-powered electric system
an electrical system having a lead-acid battery as a source of power. The battery is recharged by a charging system using either a generator or


alternator.
battery-supported CDI
capacitive discharge ignition system which uses a battery to supply primary ignition current.

bearing
a part in which a journal, shaft or pivot turns or moves.



bearing spacer
a piece of tubing used between wheel bearing inner races to prevent unwanted bearing preload as the axle is tightened.

bench grinder
a power grinder with round abrasive stones mounted on either end of a special electric motor, for rough grinding of ferrous metals.

bleeder-type needle circuit
air from carburetor air jet is mixed with fuel in body of needle jet making an air-fuel froth. The mixture is then metered into throat of carburetor by jet needle and needle jet.

blow-by
when piston rings do not effectively seal combustion pressure, allowing hot gases to blow between rings and cylinder wall. This causes overheating of piston and poor performance.

boring bar
a machine tool used to accurately enlarge a cylinder bore.

bottom dead centre (BDC)
lowest piston position in cylinder.

brake actuator cam
small cam that pivots in brake backing plate and forces brake shoe into brake

drum.

brake caliper
part of a disc brake which holds friction pads and encloses disc. As brake is applied, hydraulic fluid forces a piston in calipers toward disc, causing disc to be pinched between brake pads.

brake disc
a round, flat disc made of steel or cast iron. It is mounted on outside of wheel hub.

brake drum
a circular ring of cast iron that is part of wheel hub. It provides a place for brake lining to be applied.

brake line
special hydraulic tubing made of steel, plastic and reinforced rubber. Hydraulic brake lines must be capable of withstanding extreme pressure without deforming.

brake lining
a special high friction material made of asbestos and other materials bonded to brake shoes and brake pad plates. Brake lining produces friction and heat when it is forced against brake drum or disc.

brake pads
small circular or square asbestos inserts in a wheel caliper. They produce friction and heat when forced against the disc.

brake shoe
a cast aluminum, half-circular shoe that holds a bonded brake lining material. When brake is applied, shoe forces lining into brake drum.

brake wear indicator
index grooves, tabs, or reference lines to indicate amount of brake lining or pad wear.

brazing
type of welding using a brass alloy filler rod.

bridged ports
a vertical port division in a two-stroke cycle engine cylinder which allows use of a large port without danger of ring or piston catching.

burr
a small, rotating cutter mounted in a rotary grinder and used for metal removal (rotary file). Also, sharp, rough area around a drilled hole.

butterfly-controlled carburetor
a carburetor using a flat plate between venturi and intake manifold to regulate airflow through carburetor.

bypass valve
valve which allows fluid to flow around normal path of flow, used in oil filters.

cam follower
components in valve train that rides on cam lobe.

cam ground
oval shape of a piston to control and compensate for expansion.

cam lobe
protrusion on a camshaft that causes valve train parts to move as camshaft rotates.

cam plate
flat plate with slots that engage pins on shift forks. As plate is rotated, slots cause shift forks to move sliding gears or dogs, causing engagement and disengagement of gearbox ratios.

camshaft
shaft with protruding eccentric lobes. As camshaft rotates, lobes cause reciprocating movement of other valve train parts.

carburetor
device that mixes and delivers proper amount of air and fuel to engine at a ratio of approximately 15 parts air to 1 part fuel.

cast alloy wheel
a one piece wheel made of cast aluminum or magnesium alloy. This design is more rigid than wire spoked wheel.

cast-in sleeve
an aluminum cylinder block cast around an iron cylinder sleeve.

cast iron cylinder
a one piece cylinder assembly made of cast iron with a machined bore.

cast piston
a piston made by pouring molten aluminum alloy into a mould of desired shape.

cavitation
inadequate lubrication caused by air taking place of oil in pump.

CDI voltage amplifier
a device, used in a battery powered capacitive discharge ignition system, that steps up battery voltage to provide high primary ignition voltage.

centre of gravity
point at which any object is perfectly balanced.

centrifugal clutch
clutch engaged by centrifugal force as engine speeds up.

centrifugal oil slinger
cup-shaped centrifugal oil filter mounted to end of camshaft. As oil passes through slinger, centrifugal force removes impurities that are heavier than oil.

chain drive
use of a chain and sprocket to connect gearbox output shaft to rear wheel.

chain stretch
wear of pins and bushings of a roller or hy-vo chain, causing chain to lengthen.

chamfer
to bevel an edge of an object or to chamfer edges of port openings in a two-stroke cycle cylinder to prevent piston ring breakage.

check valve
a spring-loaded ball or piston valve that allows flow only in one direction.

chemical regulator
voltage regulator with solid state electronic devices to regulate charging system output.

circlip
a circular clip or snap ring that fits into a groove, used to locate or retain a shaft or component.

circuit
an electrical path from a power source, through wire, to components, and back to source.

clearance
amount of space between two adjacent parts.

close-ratio gearbox
a gearbox with gear ratios spaced close together.

clutch
device used to connect and disconnect engine power to gearbox input shaft.

clutch basket
part of clutch assembly containing clutch plates. Primary drive gear engages teeth on outside of clutch basket.

clutch holder
tool to secure clutch basket and clutch hub while loosening or tightening clutch security nut or primary drive gear nut.

clutch hub
part of clutch that engages with plain driven clutch plates. Clutch hub is mounted on gearbox input shaft.

clutch pressure plate
part of a clutch assembly providing pressure against clutch disc or clutch plates.
clutch release mechanism
mechanism that moves clutch pressure plate away from clutch pack, allowing clutch to slip.

coated bore
thin coating of chrome or iron applied to inside of cylinder by electroplating or wire explosion spray coating.

coil build-up
build-up of a magnetic field while current is flowing through primary windings of coil.

cold soak cleaner
a strong cleaning solvent used to dissolve and remove varnish on carburetor parts.

colour code
use of different base colours and coloured tracers on insulation of electrical wire for purpose of identification.

combustion
burning of air-fuel mixture in combustion chamber.

combustion chamber
area of cylinder head and cylinder above piston where combustion of air-fuel mixture takes place.

common sump
same oil is used to lubricate engine, gearbox, and primary drive.

compression
increased pressure caused as volume is reduced. Also, movement of suspension components against spring pressure caused by a force against the wheel.

compression gauge
gauge which measures cranking pressure between piston and upper cylinder.

compression ring
piston ring designed to seal pressure between piston and upper cylinder.

compression stroke
movement of piston from BDC (bottom dead centre) to TDC (top dead centre) with valves closed, compressing air-fuel mixture for more violent combustion.

concentric
when two or more circular parts have same centre line.

condenser (capacitor)
two metal sheets separated by an insulator used to store an electrical charge.

conical hub
a wheel hub (wire wheel) with spoke holes on brake side of wheel at a greater distance from centre of hub than spoke holes on opposite side of hub.

connecting rod
a rod made of steel or aluminum or titanium, usually having an I-beam cross section. It connects piston to crankshaft.

connecting rod kit
a parts kit consisting of connecting rod, crank pin, thrust washers and roller bearings, used in reconditioning of assembled crankshafts.

connecting rod tip
amount of radial (side) play at top of connecting rod. Measurement of rod tip is one way of determining condition of rod big end bearing.

contact points
switching device used to start and stop flow of current.

continuity
a continuous path for current flow.

conventional rear suspension
suspension used on dual-purpose and road bikes which provides less than 6 in. (152 mm) of suspension travel.

cooling fins
projections on cylinder heads, cylinders and crankcases to increase surface area for more efficient heat dissipation into air.

countershaft sprocket
output sprocket from gearbox. Mounted on output shaft in indirect drive gearbox and on high gear pinion in direct drive gearbox.

cradle frame
frame built of tubing which supports and surrounds engine.

crankcase
castings that support and contain the crankshaft, primary drive and gearbox.

crankcase leak test
pressure test done to a two-stroke cycle engine to determine if crankcase is properly sealed.

crankpin
pin or journal on which big-end of connecting rod rides.

crankshaft axles
extensions at each end of crankshaft to provide a mounting place for main bearings, primary drive or sprocket, and alternator rotor or magneto flywheel.

crankshaft reconditioning
replacement of worn lower-end components in an assembled crankshaft. This involves pressing crankshaft apart, replacing crankpin, roller bearing, thrust washer, and connecting rod, pressing crankshaft back together and trueing it (assembled crankshaft).

crankshaft wheel
portions of an assembled crankshaft that provides a mounting place for

crankpin and crank axles.

current flow
movement of electrons through a conductor.

cycle
a series of events which take place during a specific interval.

cylinder
a machined hole in cylinder block for piston, open at both ends.

cylinder block
casting attached to crankcase which contains cylinder bore, cooling fins or water jacket, and provides a means of mounting cylinder head.

cylinder bore
diameter of cylinder opening.

cylinder boring
bore diameter machined (bored) to accept oversized piston. This renews a worn cylinder.

cylinder deglazing
use of a hone to slightly roughen walls of cylinder. It produces a crosshatch pattern which aids in seating of new rings.

cylinder head
casting that seals top of cylinder and provides a mounting place for spark plug. In four-stroke cycle engine, cylinder head also contains intake and exhaust ports. Both two- and four-stroke cycle engines also have combustion chamber built into cylinder head.
cylinder honing
use of a parallel type cylinder hone to size a cylinder after boring. Proper cylinder honing provides proper texture and crosshatch.
cylinder liner
cast iron sleeve or tube pressed or cast into cylinder block to provide bore which piston moves in.

damper
device which uses oil metered through orifices to control abrupt suspension movement during extension and compression.
damper rod
tube secured to bottom of each fork slider to hold slider onto fork leg. Damper rod controls movement of front suspension by metering hydraulic fluid through orifices in rod.
decarbonize
to remove carbon build-up on piston, combustion chamber, and other parts.
depth micrometer
a precision measuring tool used to take measurements of stepped surfaces.
detergent oil
an oil which keeps particles and contaminants in suspension and has ability to neutralize acids resulting from combustion process.
detonation
a condition where excessive temperature of air-fuel mixture in combustion chamber causes uncontrolled explosive burning. As detonated flame front collides with flame front initiated by spark plug, extreme pressure is often heard as "pinging" or "knocking." Detonation can be caused by incorrect ignition timing, lean air-fuel ratio, and improper fuel.
diagnosis
process of determining cause of a failure.
dial bore gauge
a precision measuring tool which combines a telescoping gauge and dial indicator to give readings of inside diameter measurements.
dial caliper
a precision measuring tool used to determine inside, outside, or depth measurements. Measurements are displayed on a dial index.
dial indicator
a precision measuring tool using a dial index to show linear movement of components being measured.
diaphragm
a thin flexible disc of rubberized fabric which separates two cavities and uses vacuum or pressure for activation.
diaphragm spring
a slightly cone shaped metal disc which acts as a clutch pressure plate spring when flattened.
diffuser
a projection in base of carburetor venturi and at top of needle jet that aids in fuel atomization.
diode
a solid state electronic device that permits current flow in only one direction.
direct bearing lubrication
an oil injection system which feeds undiluted oil to two-stroke cycle engine main bearings and rod big-end nearing.
direct current
a continuous flow of current in same direction.
direct drive gearbox
power is transferred from clutch to input shaft (main shaft), to layshaft, to high gear pinion, which has output sprocket mounted on it.
disc brake
a brake consisting of a flat circular disc attached to a wheel. A hydraulic or mechanical caliper applies pressure to two brake pads to slow or stop disc rotation.
DOHC (double-overhead camshaft)
two camshafts located in cylinder head (one for intake, one for exhaust).
double-leading shoe
a drum brake having two leading shoes and no trailing shoes. Each shoe has its own activating cam and pivot.
double-piston caliper
a hydraulic brake caliper with two pistons and provisions for applying hydraulic pressure equally to both pistons. The caliper body is fixed solidly.
double-row chain
a chain having two rows of rollers. Duplex (double-row) chains are used for primary drives.
drive plate
a clutch plate which is indexed into clutch basket (outer hub) by tabs. Drive plate has friction material bonded to its surface. When clutch is engaged, drive plate transfers power to driven plate.
driven plate
a clutch plate which is indexed onto clutch inner hub by tabs or splines around its inside diameter. Driven plate is usually a plain plate (no friction material) and drives gearbox input shaft through clutch inner hub.
drum brake
a brake consisting of two brake shoes mounted on a backing plate. One or two cams cause shoes to expand against inside of brake drum. Brake drum is part of hub or is bolted to hub.
dry clutch
a clutch assembly that does not run in an oil bath.
dry sump
in this system, oil is gravity fed to supply side of oil pump from a remote oil tank. After oil has been pumped through fourstroke cycle engine, it is returned to oil tank by return side of oil pump.
dual-rate charging system
a charging system that switches extra coils into charging system when lights are turned on.
dwell
length of time, in crankshaft degrees, that ignition contact points are closed.
dykes piston ring
a piston ring with an L-shaped cross section designed to use combustion pressure to improve sealing.
dynamic ignition timing
use of a strobe light to check ignition timing with engine running.
electric arc welding
see arc welding.
electrodes
conductors at centre and side of spark plug that provide an air gap for an electric arc to start combustion process in engine.
electrolyte
a solution of dilute sulphuric acid used to provide a chemical reaction in a lead-acid battery.
electromagnet
a magnet which produces a magnetic field by passing electrical current through a coil wire wrapped around a soft iron core.
electromagnet
alternator an alternator which uses electromagnet to produce a magnetic field.
electromotive force (EMF)
force that causes electricity to flow because of a difference in potential between two points.
electronic ignition system
an ignition system which uses a magnetic triggering device and solid state amplifier rather than conventional contact points.
element filter
a disposable oil or air filter that uses gauze or paper as filtering material.
elliptical port shape
rounded port shape designed to prevent ring catching in large ports of two-stroke cycle engine.
emissions
byproducts of a running engine, including: exhaust pollutants, noise emissions.
endless chain
a roller chain without a master link for connections of ends. All pin links are permanently riveted.
engine
a machine that converts chemical energy into mechanical energy.
English measurement system
a measurement using the foot (12 in.) as a standard.
enrichment circuit
a carburetor system with a plunger to open and close an air-fuel circuit which discharges a rich mixture into throat of carburetor for cold starting.
eroded piston (crown)
a condition caused by detonation or pre-ignition where temperatures are raised so high that part of piston crown is melted away.
exhaust port
an opening or passage which directs flow of exhaust gases out of engine. In a four-stroke cycle, it is located in the head. With a two-stroke cycle, it is in the cylinder.
exhaust (port) timing
amount of time two-stroke cycle exhaust port is open, expressed in crankshaft degrees or piston travel.
exhaust stroke
with a four-stroke cycle engine, it is movement of piston from BDC to TDC with exhaust valve open, pushing burned gases out of cylinder.
extension
the return or stretching outward of suspension components (after compression) caused by spring pressure.

fastener
a device used to attach one part or assembly to another (nut and bolt, screw, rivet, etc.).
feeler gauge
a measuring tool made of steel blades of precise thickness used for measuring distance between surfaces.
field coil
a electromagnet used in DC generator or AC generator to produce a magnetic field.
filler rod
a metal rod that is melted into welding puddle to provide necessary bead thickness.
film strength
ability of an oil to keep moving parts from making contact with each other.
final drive
chains and sprockets or shafts and gears used to connect the gearbox output shaft to rear wheel.
flange-mounted carburetor
a carburetor mounted by a flange. The flange is bolted to a manifold on cylinder or cylinder head. An insulator block and a gasket are used to seal and insulate carburetor.
float assembly
a carburetor device consisting of plastic or hollow brass floats attached to an arm. This assembly pivots on a pin and raises and lowers, opening and closing float needle to control fuel level in float bowl.
float level
level of fuel maintained in carburetor float bowl. Controlled by float, float needle and seat.
float needle and seat
a carburetor valve, opened and closed by the float, that lets fuel into float bowl from fuel line.
fluid pressure gauge
gauge for measuring fluid pressure in a system such as oil pressure or fuel pressure.
flywheel
a weight attached to an engine crankshaft, providing crankshaft with added inertia. This helps to smooth out abrupt movement of crankshaft during power stroke and to keep crankshaft turning during non-power producing events.
flywheel magnet
magnet mounted on side of flywheel in a flywheel magneto.
flywheel magneto ignition system
an AC ignition system using a generating coil or a magnetic trigger (CDI) or contact points as well as a flywheel to provide primary ignition current and triggering. An external ignition coil is used to provide secondary current.
foaming
undesirable characteristic of oil being whipped into a froth (air and oil solution).
foot-pound
amount of work required to lift one pound one foot, used to express torque.
forged piston
a piston made by hammering hot aluminum into a mould of desired shape.
fork sliders
outer portion of fork which slides over fork leg inner.
fork tubes
long sturdy tubes usually attached to triple clamps and fitted inside fork sliders. Can also be fitted to front wheel on some modern bikes (upside down forks)
four-stroke cycle
one cycle consisting of four distinct events, intake, compression, power, exhaust. One cycle requires two revolutions of crankshaft.
friction
resistance to movement between two objects contacting each other, causes heat.
friction plate
see drive plate.
fuel filter
a small filter designed to remove dirt and water from fuel before it reaches carburetor or injection system. Filters may be made of metal or plastic screen, paper and gauze. Filters may be located at fuel tank, in fuel line, or at carburetor.
fuel line
a flexible fuel resistant hose that carries fuel from fuel petcock to carburetor.
fuel petcock
an on-off valve located at bottom of fuel tank. It may provide for reserve fuel supply and may have a filter screen and sediment bowl. Fuel line to carburetor is attached to fuel petcock.
fuel pump
a diaphragm or electric device that maintains proper fuel pressure to carburetor or injection system. A fuel pump must be used when fuel tank is located lower than carburetor and with all injection systems.
fuel system
system which stores, filters, and regulates flow of fuel to engine. It consists of fuel tank, fuel valve, fuel filters, fuel lines, air filter, carburetor, and carburetor mounting.
fuel tank
a reservoir used to store fuel for delivery to engine.
full-wave rectifier
a rectifier that converts AC to DC by inverting negative portion of AC sine wave.
fuse
a device used to protect electrical circuits from overloading. A link in fuse melts and opens circuit if current is above normal rating.
gas-charged shock absorber
a shock absorber using a pressurized gas such as nitrogen to help prevent changes in damping as shock absorber heats up.
gearbox
a series of shafts and gears which varies ratio of engine to rear wheel speed. Motorcycle gearboxes use from two to seven speeds or ratios.
gearbox indexer
a plunger and spring or pivoted lever that indexes into dimples or slots in shift drum or cam plate. It provides positive positioning of shift drum or cam plate in each gear.
gear oil pump
an oil pump with gear type teeth to move oil.
gear ratio
ratio of rotation of rotating part compared to another rotating part.
generator
a device which converts mechanical energy into electrical energy, producing direct current (DC).
graduated cylinder
a container, calibrated in cubic centimetres or millimetres used for accurate measurement of fluids such as fork oil and gearbox oil.
gusset
a reinforcing plate or boxed section used to prevent flexing of frame or swing arm.
half-wave rectifier
a rectifier which blocks one-half of AC sine wave to convert AC into DC.
heat transfer
movement of heat from one area to another.
heliarc welding
a type of electric arc welding which uses inert gas to shield area around arc.
helical gear
a gear having teeth that are slightly angled. Helical gears (used for primary drives) are quiet in operation, but absorb a slight amount of power due to side thrust.
hemispherical combustion chamber
a combustion chamber shaped like a round dome, allowing use of large valves placed opposite each other in chamber.
high-gear pinion
top gear on main shaft in direct drive gearbox. All ratios drive through high-gear pinion, which has output sprocket mounted to it.
holed piston
a condition caused by severe detonation or pre-ignition, where a hole is eaten or burned through crown of piston as a result of extreme heat and pressure.
horsepower (h.p.)
a unit for measuring the power of engines, motors, etc.; 1 h.p. equals 550 foot-pounds per second.
hydraulic brake
a braking system using hydraulic fluid, piston, and cylinders to provide extremely high pressure for brake application.
hydraulic clutch
a system which uses hydraulic pressure to disengage clutch.
hy-vo chain
a very strong chain made up of toothed plates positioned side by side and held together by pins. Advantage of this type of chain is great strength and quiet operation.

idle mixture
air-fuel ratio with throttle twist grip closed. Idle mixture is controlled by pilot jet and pilot adjustment screw in carburetor or computer in electronic fuel injection system.
ignition coil
a step-up transformer that uses induction to increase battery voltage to over 20, 000 volts.
ignition-generating coil
coil in a flywheel magneto that provides primary ignition current.
ignition system
part of the electrical system responsible for providing a high voltage at proper time to ignite air-fuel mixture. Battery and coil, electronic, magneto, and CDI are the four systems commonly used.
impeller
finned wheel that produces pressure and flow when spun in enclosed housing of oil pump or water pump.
indirect drive gearbox
a gearbox where power is transferred from clutch to input shaft to output shaft. Output shaft has a sprocket mounted on one end.
induction
production of current flow resulting from magnetic field cutting through a conductor.
inertia
tendency of a stationary object to resist movement or tendency of a moving object to continue moving in same direction.
injection system
an oil pump and oil lines that deliver oil to a two-stroke cycle engine as it is needed. Also, fuel system which meters gasoline into engine intake ports.
in-line cylinders
cylinders positioned in a row or side by side.
in-line filter
a small fuel or oil filter that replaces a section of line or hose.
input shaft
shaft of a gear box which carries power into gearbox. Clutch assembly is mounted on gearbox input shaft.
inside micrometer
a precision measurement tool used to take accurate measurements of inside surfaces.
insulator block
a fibre or rubber block that insulates carburetor from engine heat, used with flange-mounted carburetors.
intake manifold
a sleeve or flange made of rubber or metal to attach carburetor to intake port.
intake port
an opening or passage that directs flow of air-fuel mixture into engine. In a four-stroke cycle engine, intake port is located in cylinder head. In a two-stroke cycle engine, intake port is located in cylinder or crankcase.
intake stroke
in a four-stroke cycle engine, movement of piston from TDC to BDC with intake valve open, drawing air-fuel mixture into cylinder.
intake timing
amount of time two-stroke cycle engine intake port is open, expressed in crankshaft degrees or piston position.
internal combustion engine
an engine that burns fuel inside rather than outside engine, as does a steam engine (external combustion engine).
jet
a carburetor component, usually made of brass, which meters flow of fuel to venturi. Fuel is metered by a small hole drilled through centre of jet.
junction block
a device that transfers action of a single cable to two or more cables.
key
parallel-sided piece inserted into groove cut part way into each of two parts, which locates and prevents slippage between parts. Also known as a woodruff key.
keystone piston ring
a piston ring with a tapered cross-section designed to use combustion pressure to aid in sealing.
kinetic energy
energy associated with motion. An internal combustion engine produces kinetic energy (crankshaft rotation).
lateral runout
side-to-side movement (wobble) of a wheel rim.
lathe
a machine tool used to spin, cut, and shape a metal part with a movable cutting tool.
lay shaft
second shaft in a direct drive gearbox. It transfers power from input shaft to high gear pinion.
lean
an air-fuel ratio that contains extra air compared to fuel.
lever and pivot
a clutch release mechanism in which a pivoted lever attached to clutch cable disengages clutch by pushing plate away from clutch plates, allowing them to slip. Lever and pivot may act directly on pressure plate or through a push rod.
lifter
a hard surface shaft with a radius or roller at one end that rides on cam lobe.
liquid cooling
use of liquid piped through water jackets, thermostat, and radiator to dissipate heat.
long travel rear suspension
suspension used on current competition dirt bikes to provide more than 6 in. (15 cm) of travel.
lower end
portion of an engine from cylinder base downward, including connecting rods.
lubricating film
a thin coating of lubricant (oil) that prevents contact between moving parts.
lubrication
use of lubricants (oil, grease) to reduce friction.
magnetic field
invisible lines of force surrounding a magnet or a conductor with current flowing through it.
magnetism
an invisible force that attracts ferrous metals.
magneto
see flywheel magneto.
magneto-supported CDI
a capacitive discharge ignition using a generating coil in magneto to produce primary ignition current.
main fuel circuit
carburetor circuit that controls air-fuel ratio from three-fourths to full throttle opening. Main jet meters fuel in this circuit.
main jet
a carburetor fuel metering jet, usually mounted at base of carburetor body, to control air-fuel ratio from three-fourths to full throttle.
manifold injection
injector oil is pumped into the intake port of two-cycle engine.
master cylinder
components in a braking system that produces hydraulic pressure for system.
master link
a pin link that has one removable side plate located by a clip, or is staked (punched) in place. This allows a convenient way of separating chain.
mating parts
two or more parts that contact each other during operation and set up wear patterns.
mechanical brake
a braking system that uses a mechanical advantage by way of levers and cables or rods to apply brakes. A braking system not using hydraulic fluids or hydraulics.
mechanical caliper
a disc brake caliper actuated by a lever and cam rather than hydraulic fluid.
mechanical voltage regulator
a voltage regulator using an electromagnet to open or close contact points, varying output of a DC generator or electromagnet alternator.
metric system
a measurement system that uses the meter (39.37 in.) as a standard.
mild port timing
two-stroke cycle engine ports open for a relatively short time, providing for a broad power band.
motorcycle
a two-wheeled vehicle powered by an internal combustion engine.
multi-grade oil
an oil that flows like a thin oil when cold, but lubricates like a thicker oil when hot. For example, 10W40 at 0
multi-plate clutch
a clutch assembly using more than one driving plate and more than one driven plate.
multiple ports
use of many small transfer ports rather than two large ports in two-stroke cycle cylinder. This can give improved scavenging.

needle bearing
an antifriction bearing utilizing hardened steel rollers between hardened races or parts.
needle circuit
carburetor circuit that controls air-fuel ratio from one-fourth to three-fourths throttle opening. The jet needle and needle jet meter fuel flow in this circuit.
negative terminal
with an excess amount of electrons which flow toward positive terminal.
neutral indicator switch
a switch, usually mounted on end of shift drum, which completes circuit of neutral indicator light when gearbox is in neutral.
non-primary kickstart
a kickstart system using gearbox input shaft and clutch hub to connect kickstart lever to crankshaft. For starting, gearbox must be in neutral and clutch engaged.
non-unit construction
engine design with separate engine crankcase and gearbox case.
nylon screw clutch release
a clutch release mechanism that uses a coarse, square threaded nylon screw for clutch disengagement.
ohm
unit used to measure resistance in an electrical circuit or component.
ohmmeter
an instrument that measures resistance.
oil bath
oil level is just high enough so it splashes around inside case or housing. Lubricates gearbox, primary drive ass well as ring and piston.
oil control ring
piston ring designed to remove excess oil from cylinder wall, usually bottom ring.
oil pump
a device that provides oil under pressure for engine lubrication.
oil pump bleeding
removal of air from supply line and pump in a two-stroke cycle oil injection system.
oil slinger
a circular, lipped disc used in direct bearing oil injection to feed oil to rod big end.
opposed cylinders
cylinders positioned opposite each other in same plane.
O-ring
a ring made of neoprene that is used to provide a positive seal. It usually fits into a groove slightly shallower than O-ring, and mated against a flat surface to provide a seal for oil, fuel, or air.
O-ring chain
roller chain that uses O-rings to permanently seal lubricant into area between pins and bushings.
out of roundness
cylinder wear caused by piston thrust. This results in wear to front and back of cylinder. Cylinder wears oval shaped rather than round.
output shaft
gearbox shaft that transmits power to final drive at a selected ratio.
outside micrometer
a precision measuring tool for taking accurate measurements between outside surfaces.
overall gear ratio
ratio of crankshaft revolutions to rear wheel revolutions.
overflow tube
a tube that is open at both ends and mounted in bottom of carburetor float bowl. If float sticks or float needle does not seat properly, excess fuel flow out overflow tube rather than into throat of carburetor.
oxidized oil
oil that has been chemically combined with oxygen as a result of excessive heat, oil agitation or exposure to combustion contaminants.
oxyacetylene (gas) welding
a type of welding (metal fusion) which burns a mixture of oxygen and acetylene to provide a high temperature flame.

parallel circuit
a circuit where current is provided to each component independently (each component has own ground). The failure of one component does not affect rest of circuit.
permanent magnet alternator
an alternator using permanent magnets to produce a magnetic field for AC production.
pilot air screw
a screw mounted on side of carburetor that allows fine adjustment of air-fuel ratio in pilot circuit of slide type carburetor.
pilot circuit
a carburetor circuit that provides proper air-fuel ratio from approximately zero to one-eighth throttle opening. It basically consists of a pilot jet, pilot air screw or pilot fuel screw, and a pilot discharge port.
pilot jet
jet that meters fuel for pilot circuit.
pinion gear
a small gear that either drives or is driven by a larger gear.
piston block
a slotted block used to support pistons for cylinder installation. Also, may be used in conjunction with a piston pin to lock camshaft.
piston (braking system)
a moveable part of a master cylinder or wheel caliper. Master cylinder piston produces pressure and caliper piston applies that pressure to brake disc, slowing or stopping wheel.
piston crown
top of piston, directly exposed to combustion pressure and heat.
piston (engine)
a cylindrical part, closed at one end, which moves up and down in cylinder. Open end is attached to connecting rod. Combustion pressure is exerted on closed end of piston, causing connecting rod to move and camshaft to turn.
piston pin boss
a strengthened section of piston extending to inside of piston crown. It supports piston pin.
piston pin hole
machined hole through piston wall where piston pin and retaining circlips are mounted.
piston port
two-stroke cycle piston skirt used to control intake port opening and closing.
piston ring (compression)
a split cast iron band, sometimes chrome plated, designed to seal combustion pressure above piston.
piston ring end gap
distance between ends of a piston ring when installed in cylinder. This clearance is measured with a feeler gauge. Ring must be straight in cylinder as if installed on piston.
piston ring groove
groove machined in piston to accept piston rings.
piston ring (oil control)
a split cast iron or steel band used to scrape excess oil from cylinder wall. Sometimes designed as a three-piece unit.
piston seizure
overheating of piston to point where it will no longer move freely in cylinder.
piston skirt
part of piston below bottom ring and pin boss.
plain bearing
a split or circular type bearing in which a part slides, turns, or pivots.
plain plate
see driven plate.
plunger oil pump
an oil pump that uses a piston, or plunger, and check valves to move oil.
polarity
direction of current flow.
port window
port opening in a two-stroke cycle engine cylinder wall.
positive
electrical terminal having a deficiency of electrons and attracts electrons from negative terminal, causing current flow.
positive carburetor linkage
a carburetor linkage designed to positively open and close one or more carburetor throttles, actuated by one cable for opening and another cable for closing.
power
ability to do work or rate of work being done.
power stroke
in four-stroke cycle engine, movement of piston from TDC to BDC with intake and exhaust valves closed, after ignition and combustion of compressed air-fuel mixture.
power transmission
a system of gears, chains, sprockets, and shafts that transfers power from crankshaft to rear wheel in varying ratios.
power transmission shock absorber
a compensator cam, rubber pads, or springs in primary drive, gearbox, drive shaft, or rear wheel, provides means of cushioning loading of gearbox.
preignition
premature ignition cause by "hot spots" in combustion chamber that ignite air-fuel mixture before spark plug "fires." This causes uncontrolled combustion and rapidly raises piston and cylinder head temperatures (similar to detonation).
premix
two-stroke cycle engine lubrication provided by oil mixed with fuel in fuel tank.
pressed-in sleeve
cast iron cylinder sleeve in interference fit into aluminum cylinder block.
primary chain drive
a primary drive design that uses a chain and sprocket to transfer engine power from crankshaft to clutch.
primary drive
use of chain, gear, or belt drive to connect crankshaft to clutch and gearbox into shaft.
primary ignition circuit
section of ignition circuit including contact points, condenser, and primary windings of ignition coil, power supply (battery or ignition generating coil), kill switch, ignition switch, and related wiring.
primary kickstart
a kickstart system that connects kickstart lever to crankshaft through clutch basket. Gearbox can be in gear for starting if clutch is disengaged.
primary reduction
a gear reduction usually about three to one, accomplished by primary drive.
primary-type needle circuit
fuel metered by clearance between jet needle and needle jet is partially mixed with air from air jet and discharged into venturi of carburetor.
primary winding
hundreds of turns of wire in an ignition coil to provide build-up and collapse of a magnetic field, including voltage in secondary.
profile
contour or shape of camshaft lobe.
push rod (pushrod)
in four-stroke cycle engine, push rods provide means of transferring tappet movement to rocker arm, which opens valves.

rack and pinion clutch release
a clutch release mechanism using pinion gear and a rack gear to disengage clutch.
radial runout
up and down movement of a rotating part (wheel rim, flywheel, etc.).
radiator
a heat exchanger that reduces coolant temperature in a liquid cooling system.
radical port timing
ports open for a relatively long period of time.
rear housing
an aluminum case which provides a mounting place for shaft drive ring and pinion gears. This housing is sealed and carries oil that lubricates ring and pinion gears.
reciprocating weight
weight of any engine parts moving back and forth while engine is running: pistons, rings, piston pin and circlips, push rods, valves.
rectifier
a device that converts AC (alternating current) into DC (direct current) for battery charging.
reed cage
an aluminum frame providing a mounting place for reed petals in two-stroke cycle engine.
reed petals
movable parts of reed valve assembly.
reed valve
a one-way valve place in intake port of a two-stroke cycle engine. It prevents backward flow of crankcase air-fuel mixture.
regulator
a device that controls alternator or generator charging current to battery.
relief valve
a spring-loaded valve that regulates maximum pressure of enclosed system.
resistance
characteristic of an electrical circuit to resist flow of current, measured in ohms.
rich
an air-fuel ratio that contains extra fuel compared to air.
ridge
an unworn portion or ledge at the top of cylinder formed above end of ring travel.
rim offset
distance a wheel rim is set off-centre (lateral) to a wheel hub. Rim offset is sometimes needed for drive sprocket clearance.
rim strip
a rubber strip installed around centre of a wire wheel rim to protect inner tube from being punctured by spokes.
ring and pinion contact pattern
area of contact between teeth of ring gear and teeth of pinion gear. Checked with red lead.
ring gear
a large gear in shaft drive housing. It is driven by pinion gear.
ring land
solid area of piston which supports rings, located between ring grooves.
rocker arm
a pivoted arm that converts upward movement of push rod to downward movement of valve.
roller bearing
an antifriction bearing consisting of hardened steel inner and outer races, separated by hardened steel rollers.
roller chain
a chain made up of pins, side plates, bushings and rollers. Roller links are connected by pin links to achieve desired length. Ends are usually connected by a pin link which has a removable side plate, called a master link.
rotary grinder
a high rpm hand held grinder using small grinding stones or burrs for metal removal in cramped or hard to get at areas.
rotary valve
a circular disc with a portion removed. It covers and uncovers intake port of two-stroke cycle engine. Disc is keyed to crankshaft.
rotor oil pump
an oil pump that uses an inner and outer rotor to move oil.
runout
out-of-round condition of a rotating part.
scavenging
inertia-caused movement of gases through cylinder and exhaust system of a two-stroke cycle or four-stroke cycle engine.
schematic
a diagram representing an electrical system.
scraper ring
dual-purpose piston ring that helps seal combustion pressure as well as control oil.
secondary ignition circuit
part of ignition systems consisting of secondary winding of ignition coil, spark plug wire, spark plug terminal, and spark plug.
secondary winding
thousands of turns of fine wire in an ignition coil. It uses induction to step up voltage as a magnetic field is rapidly collapsed in primary windings.
sediment bowl
a cup located at bottom of fuel petcock designed to prevent flow of dirt and water into fuel line.
selenium rectifier
a device that converts AC to DC through use of selenium plates.
series circuit
a circuit in which current must follow a single path through each component in sequence before reaching ground. If one component fails, entire circuit is open.
shaft drive
use of a drive shaft, universal joints and gears to connect gearbox output shaft to rear wheel.
shift drum
a drum shaped gearbox component with slots around its outside diameter. It engages with shift mechanism and shift forks. As drum is rotated, drum slots cause shift forks to move sliding gears or dogs causing engagement and disengagement of various gearbox ratios.
shifting fork
a flat forked gearbox component that engages with a slot in a sliding gear or dog. Shifting forks slide back and forth on lateral shafts. Rotation of shift drum or cam plate causes shift fork to move its sliding gear or dog to engage with another gear, locking both gears to shaft.
shift linkage
hinged lever or levers that transfer movement of shift lever to shift drum or cam plate.
shift stopper
a fork or pin that limits movement of shift drum to prevent overshifting.
shim
a spacer used between two parts to achieve proper clearance.
shim bucket
a cylindrical shaped part in DOHC (double overhead camshaft) valve train. It is located between valve and camshaft and provides a receptacle for valve lash adjustment shims.
shock absorber
rear suspension unit made up of a coil spring and a hydraulic damper. It prevents spring oscillations. See also power transmission shock absorber.
siamese crankshaft
crankshaft configuration where two rods are mounted on same crank pin (journal). One rod is forked the other is mounted on inside of fork.
side-by-side crankshaft
crankshaft configuration where connecting rods are mounted next to each other on same crankpin (journal).
sine wave
a graphical representation of 360 degrees of rotation, representing change in direction of single-phase AC.
single-leading shoe
a drum brake having two shoes: one is leading and one is trailing. Leading shoe tends to wedge itself into drum providing more braking action than trailing shoe.
single-phase AC
alternating current that reverses direction of flow every 180 degrees.
single-piston caliper
a laterally floating disc brake caliper that uses one hydraulic piston to apply both brake pads. As pressure is applied to piston, it pushes one pad against disc. Other pad is solidly mounted on opposite side of caliper and makes contact with disc as caliper floats.
single-row chain
a conventional roller chain with one row of rollers.
sleeve-mount carburetor
a carburetor mounted on an aluminum manifold by a pinch bolt that clamps carburetor spigot over a plastic or fibre- insulating sleeve.
slide-controlled carburetor
a carburetor using a throttle slide (plunger) to regulate venturi restriction (throttle opening).
slide cutaway circuit
carburetor circuit which controls air-fuel ratio from one-eighth to one-quarter throttle opening. Height of cutaway portion of slide controls how much air is mixed with fuel. Fuel is metered by pilot jet, needle jet and jet needle.
sliding gear (dog gear)
a gear splined to its shaft and moved side to side by a shifting fork. A sliding gear has dogs on its lateral face that engage with holes or dogs in adjacent gears.
SOHC (single overhead camshaft)
a single overhead camshaft located in top of cylinder head.
solid roller chain
roller chain using a one-piece roller and bushing assembly.
spigot-mount carburetor
a carburetor mounted by clamping spigot into a rubber sleeve manifold.
spindle (steering fork)
a shaft that is secured to upper and lower triple clamps. It pivots on bearings mounted in steering head.
spoke-crossing pattern
number of spokes crossed on same side of hub by any one spoke.
spoked wheel
a wheel consisting of a rim, spokes, nipples and hub. Spokes are laced between hub and rim and are attached to rim by nipples. Thirty-six or forty spokes are termly used.
spoke torque wrench
a small torque wrench used to accurately adjust spoke tension.
spring preload
static installed length of a spring subtracted from its free length. In suspension system, spring preload determines ride height of motorcycle.
spring tester
a device that measures spring pressure in relation to spring length.
sprocket
a circular plate with teeth machined around outside to engage links of a chain.
stamped frame
a frame stamped from pieces of sheet metal that are welded together to provide support for engine and suspension.
stamped wheel
a wheel assembly using stamped sheet metal spokes in place of small wire type spokes. A stamped wheel resembles a cast alloy wheel in appearance.
stand-off
backward flow of air-fuel mixture in intake tract caused by radical port or cam timing.
starter system
carburetor system that provides a rich mixture for cold starting (tickler, choke, enrichment circuit). Also, electrical circuit for cranking engine, including: starter switch, relay, battery, and starting motor.
static ignition timing
use of a buzz box, test light or ohmmeter to check ignition timing without running engine.
steering damper
a device that uses friction or a hydraulic damper to reduce steering oscillation.
steering head
forward part of frame providing a mounting place for bearings that locate and support steering spindle and fork assembly.
steering offset
distance between steering axis and axis on which axle pivots. Steering offset is accomplished by offsetting axle or triple clamps.
steering rake
angle of steering axis from vertical, given in degrees.
steering trail
distance along ground between lines drawn vertically through front axle and down centre of fork tubes and sliders.
straight-cut gear drive
a gear drive which uses gears having straight-cut teeth, used for one type of primary drive.
straight-cut offset gear
a gear design using straight-cut gears installed side-by-side and one-half tooth out of phase. This gear design will eliminate noise caused by backlash common to conventional straight-cut gears.
stroke
movement of piston from TDC to BDC or from BDC to TDC.
sump
lowest position of crankcase, containing oil.
surface plate
a block of granite ground and lapped to provide a very smooth, flat surface. It is used for checking straightness of cylinders, cylinder heads, and crankcase joints.
suspension
components that absorb road surface irregularities to smooth motorcycle ride. It is designed to permit controlled wheel movement over irregular surfaces. Basic parts include forks, swing arm and shock absorbers.
swing arm
main member of rear suspension that provides a mounting place for rear wheel and one end of shock absorbers.
swing arm pivot
forward part of swing arm, where it is attached to frame and pivots on bushings or bearings.
symmetrical
two sides or events being identical. For instance, two-stroke exhaust timing is symmetrical. Exhaust port opens and closes at same crankshaft position before and after TDC.
symmetrical hub
a wheel hub (wire wheel) that has spoke holes on each side of hub at same distance from hub center.
synchronize
adjustment of carburetor throttles on two or more carburetors, so that all throttles are open same amount at any position of throttle twist grip.

taper
a small diameter at one end of part, for instance: tapered piston or taper cylinder bore.
telescopic fork
front suspension unit made up of two fork tubes and two sliders that telescope up and down tubes against spring pressure.
telescoping gauge
a "T" shaped instrument used to duplicate distance between inside parallel surfaces (cylinder bore for example).
thermostat
a temperature sensitive device used in a liquid cooling system to adjust flow of coolant as coolant temperature changes.
three-phase AC
alternating current with a 120-degree phase difference. Three wires are needed to carry current.
throttle cable
a cable consisting of an outer housing and an inner cable that connects carburetor to throttle twist grip.
throttle stop screw
an idle speed adjustment screw used in slide type carburetor. This screw contacts base of throttle slide. As screw is turned in, throttle slide is raised, increasing idle speed.
throttle twist grip
a device mounted on end of handlebar that locates one end of outer throttle cable and pulls inner cable as twist grip is rotated.
thrust washer
a washer used to bear side thrust loads or provide lateral location.
tickler system
a spring-loaded plunger in carburetor that can be depressed to push float assembly down. This allows fuel to flow into float bowl, raising float level temporarily for cold starting.
tire pressure gauge
a pressure gauge used to check tire air pressure.
top dead center (TDC)
uppermost piston travel in cylinder.
top end
part of an engine from cylinder base up, including pistons but not connecting rods.
torque
a twisting force measured in foot-pounds or newton-metres.
torque converter
a fluid turbine that takes place of clutch in primary drive. Oil is used to transmit power through torque converter depending upon engine rpm. Used in automatic transmissions.
torque pattern
a specific sequence of tightening fasteners to help prevent warping of components.
torque wrench
a wrench calibrated to allow for accurate application of tightening force to fasteners.
transfer port
opening in cylinder wall of a two-stroke cycle engine that connects cylinder to crankcase.
transfer (port) timing
amount of time transfer port is open, expressed in crankcase degrees or piston position.
transmission
see gearbox.
triple clamps
a pair of sturdy brackets that provide a mounting place for fork legs and steering spindle. Triple clamps attach forks to frame through spindle, steering head and steering head bearings.
triple-row chain
a chain having three rows of rollers. Triplex chains are used for primary drives.
two-stroke cycle
a cycle of overlapping events (intake, transfer, compression, power, exhaust) which all occur during one revolution of crankcase.
unit construction
engine design has one crankcase to house gearbox, clutch, primary drive, and engine.
universal joint
a flexible joint that allows changes in angle of drive shaft.
vacuum
pressure that is less than atmospheric pressure.
vacuum-controlled carburetor
a carburetor using a butterfly to regulate airflow and a vacuum controlled piston to regulate venturi restriction.
vacuum gauge
a gauge that measures pressures which are lower than 14.7 lb. per square inch (101 kPa) at sea level.
vacuum piston
throttle piston used in a vacuum operated CV carburetor. One type uses a diaphragm at top with a small diameter piston. Other type uses a large diameter piston in a vacuum cylinder.
valve
a device that controls flow by opening and closing. For instance, fuel valve controls flow of fuel from fuel tank to carburetor. Intake valve controls flow of air-fuel mixture into cylinder.
valve overlap
period of time when intake and exhaust valves in a four-stroke cycle engine are open at same time.
valve stem
portion of valve that slides in valve guide and provides a mounting place for valve spring upper collar and keepers.
valve train
all components which directly influence valve operation (cam, cam chain, cam followers, valves, valve springs, valve collars, and keepers in SOHC engine).
varnish
a build-up of oxidized oil or fuel.
vee-cylinders
cylinders positioned at angles to each other forming a "V".
vent
a tube or drillway going from top of float chamber to atmosphere. This prevents build-up of pressure or vacuum in float chamber.
venturi
a restriction in a tube that cause an increase in air velocity, resulting in decrease of pressure (increase in vacuum) at restriction.
vernier caliper
a precision measuring tool used to determine inside, outside, or depth measurements. A linear vernier scale is used.
vertical mill
a machine tool that removes metal with a rotating cutter mounted vertically.
viscosity
the resistance that oil offers to flow when it is subjected to stress (thickness or weight).
voltage
force causing electron flow in conductor.
voltmeter
an instrument that measures electrical pressure (EMF, voltage) in electrical circuits.
watt
unit of measurement of electrical power (rate of doing work).
wear limits
minimum and maximum acceptable size of a component.
welding
use of heat to fuse two pieces of metal together.
wet clutch
a multi-plate clutch that runs in an oil bath (primary drive).
wet sump
four-stroke cycle engine sump (crankcase) in oil reservoir.
wheel bearing grease
a special, heavy duty, high temperature grease used to lubricate wheel bearings.
wide ratio gearbox
a gearbox having wide ratio spacing between gears. A wide ratio gearbox is commonly used in enduro (off-road) and trials motorcycles.
wire gauge
a measuring tool made of precisely sized wire. It is for measuring distance between irregular surfaces (spark plug gap for example).
wire wheel
see spoked wheel.
woodruff key
parallel-sided piece inserted into groove cut part way into each of two parts, which locates and prevents slippage between parts.
Zener diode
a solid-state device used to regulate voltage in motorcycle charging systems.


















ABS
(İng. Anti-lock Brake System , Alm. “Anti Blockier Sytem” - Wabco Gmbh tarafından patentli)Kilitlenme önleyici fren sistemi. Sistem, yol şartlarına göre kilitlenmeyi hissedip, bilgisayarda değerlendirmekte ve durma süresince birden cok kez freni açıp kapayarak kilitlenmeyi önlemektedir


Artçı Motosiklet
Motosikletlerle grup sürüşü sırasında en arkadan gelen motosiklete verilen genel isim

Alternatör
(Fr.Alternateur , İng.Alternator) Motor çalışırken ürettiği doğru akım (DC) ile elektrik sistemini besleyen güç üretim ünitesi.

Antifriz
(İng.Anti freeze) Soğutma suyunun donmasını engellemek için radyatöre konulan , %50’si glisol , %50’si su olan bir sıvıdır.

Avans
Ateşleme avansı olarak da bilinir. Silindir içinde sıkıştırılan yakıt hava karışımının tamamen yanabilmesi için gereken süredir.


Balaklava
Genellikle kış kullanımı için, bazen sadece gözleri, bazen de tüm yüzü açık bırakan , kafaya geçirilen bir nevi bere.

Beemer
BMW motosikletlere verilen , yerleşik argo bir tanımlama.

Beygir Gücü (BG)
(İng.Brake Horse Power) 75 Kg’lık bir ağırlığı 1 metre hızla hareket ettirmek için gereken güç. Motorun gücünü belirtmek için kullanılır. 1 KW = 1,36 metrik HP ‘dir (Yaklaşık olarak) Kısaltma olarak bazen CV (İt. Cavalli Vapore) , PS (Alm.Pferde Starke) , CV (fr.Cheval Vapeur) veya CV (Sp. Caballo de Vapor)karşılaşılabilir. SAE (Society of Automotive Engineers – USA)‘ye göre 1 HP = 1,0138 PS (DIN - Deutsches Institut für Normung) . Not: 1 metrik HP = 1 PS

Boxer
(ing.)İlk kez Ferdinand Porsche tarafindan tasarlanan , iki pistonun 180 derece acıyla yere paralel ve birbirlerine karşı çalıştığı motor sistemi. Piston kollarını birbirlerine karşı çalıştığı için boksör hareketine benzetilerek bu isim verilmiştir. BMW R serisi motosikletlerde bu tip motor kullanılmaktadır. (Flat Twin de denir)

Buji

(Fr.Bougie , İng. Spark Plug) Ateşleme ünitesi. Porselen bir yalıtkanın içine yerleştirilmiş bakır bir çubuk ve bunun ucunda + ve – kutupları temsilen aralığı genellikle 1- 3 mm olan iki metal parça arasında oluşturduğu yüksek voltajlı kıvılcım vasıtası ile sıkıştırılmış benzin ve hava karışımını ateşlemeye yarayan motor parçası.

Bobin
(Fr.Bobine) Akü voltajını bujide atlama yapıp kıvılcım oluşturabilecek seviyede yükselten ( 15.000 – 25.000 Volt , düşük amper) araçtır.

Countersteer
(İng.) Gidonun dönülmesi gereken virajın yönünün tersine çevrilmesi işlemine verilen ad. Solu it sola dön , sağı it sağa dön tekniği. (Detaylı eğitimi almadan denemeyin)

Custom
(İng.) Sipariş üzerine özel üretilmiş , veya zevkinize göre kendinizin kişiselleştirdiğiniz her tip motora verilen ad. (Custom XT200 , custom CBR900RR gibi..)

Cruiser
(İng.) Fabrika üretimi tüm gezinti motorlarına verilen ad. Yere yakındırlar. Sürat ve viraj almak için uygun değildirlerdir. Seri olarak üretilmiş tüm Harley Davidson’lar , Honda Shadow-Magna , Kawasaki Vulcan-EN serileri vs. bu gruba girerler)


Chopper
(İng.) Tam kelime karşılığı helikopterden gelmedir. Seslerinin benzemesinden çağrışım yapılmış olabilir.Ön çatal açısı (rake) geniş olan cruiser tipi özel üretim motorlara verilen isimdir. Seri olarak üretilmezler. webmaster dan not: helikopterler havayı kestikleri için chopper diye anılırlar. Genelde cruiser tipi motosikletlerin kesilip biçilerek yada tamamen elde yapanın kendi tasarımı olarak ama yine kesip biçilerek yapılmasından kaynaklanan bir terimdir.

Conta
(İt.Giunta , İng.Gasket) Sızdırmazlığı sağlayan , genellikle ısıya dayanıklı kauçuk , kösele veya kurşun gibi malzemelerden yapılmış ince parçalara verilen genel ad. (Örnek: Silindir bloğu ile silindir kapağı araındaki sızdırmazlığı sağlayan silindir contası)

D.O.H.C.
(İng. Double Over Head Camshaft) Çok supaplı (silindir başına 4 ve fazlası) motorlarda motor üstünde bulunan supap açma kapamaya yarayan çift kamın kısaltılmış hali.

Debriyaj Kuru
Otomobillerde bulunan sistem gibi , daha çok yüksek torklu motosikletlerde motor hareketi ile dişli kutusunu ayıran kuru(yağsız) debriyaj sistemidir.

Debriyaj Islak
Şanzıman yağının içinde bulunan birçok kavramadan oluşur. Kavramaların arasında yağ bulunur. Daha çok yüksek devirli spor motosikletlerde kullanılır (soğutma amaçlı)

Desmodromic
Motosiklet motorunda özel bir supap kontrol sistemi. Geleneksel yay ile geri çekme yerine ilk kez Mercedes tarafından kullanılmış ve şimdi Ducati motosikletlerinde gelenekselleşmiş bir sistemdir. Daha yüksek devir ve beygir gücüne imkan tanır

Dirt Bike
Özel bir yariş türü olan çamurlu pistlerde yarışmak amacı ile üretilmiş motokros tipi motosikletlere verilen ad

Disk Fren
Frenlemenin fren balatası – kaliperler ve çelik disk üçlüsü ile sağlandığı sistem.

DOT
(İng. Department of Transportation) Ulaşım departmanın belirlediği standartları imleyen kısaltma.

Dört Zamanlı
Pistonun her devrinde 4 işlem yapılır. 1.zaman:Hava veya yakıt hava karışımını emme 2. Sıkıştırma, 3. Ateşleme/Patlama (Kimyasal enerjinin mekanik enerjiye dönüştüğü nokta 3.Egzozdan atma.

Dual Sport
(İng.) Hem iyi yol hem de kötü yol koşullarına cevap verebilecek nitelikteki motosikletlere verilen ad.

Distribütör
(Fr. Distributeur) Motorun ateşleme sırasına göre bujilere akım dağıtan araç.

Easy Rider
Meşhur motosiklet filmi.(1969, Peter Fonda, Dennis Hopper, Jack Nicholson)

Egzoz
(İng. exhaust) Motorlu tasitlarda yanan gaz veya bunun duzenegi (Yanlış kullanım : eksoz, egzos , egsoz , ekzost.....)

Enduro
(İng. Endurance) Kelime anlamı dayanıklılıktan gelen bu terim hızdan çok zamana karşı belli tecrübe ve yeteneklerin ön plana çıktığı yarışlara verilen genel addır

Enduro Motosikleti
(İng.) Motokros motosikletinden farklı olarak daha aralıklı vites oranları ve 650cc’ye kadar da motor hacimleri olabilir. Daha hızlı olmakla birlikte motokross motosikletlerinden daha ağır olurlar.


Entegre Fren
Tek bir pedal veya kola fren uygulandığında işlemci veya mekanik dağılım ile ön-arka tekerleklere giden hidrolik basıncını ayarlayarak motosikletin en kısa/güvenli şekilde durmasını sağlayan fren sistemi.

Flat Twin
(İng.) İki pistonun 180 derece acıyla yere paralel ve birbirlerine karşı çalıştığı motor sistemi.(Bknz.Bokser)

Full-Face Kask
(İng.) Çenesi açılıp kapanmayan , yarım olmayan ve kafanın tamamını koruyan kask tipine verilen ad. En iyi korumayı sağlayan kask tipidir. Kullanımı nispeten biraz daha zordur.

Gidon
(fr.guidon) Motosikleti yönlendirmeye yarayan tutamaç.Yönelteç (Yanlış kullanım : didon)

Gidon Amortisörü
Ani bir çukura girildiğinde ön tekerleğin motosikletin yol çizgisinden ani sapmasını engellemek için insan gücünün karşılayamayacağı büyüklükteki yükü absorbe etmek için kullanılan düzenek. Genellikle yarış motosikletlerinde kullanılırlar.

GPS
(İng. Global Positioning System) Küresel konumlama sistemi. Dünya yörüngesindeki yaklaşık 24 uydudan gelen sinyalleri analiz ederek noktasal hassasiyette konumunuzu belirlemeye yarayan sistem. Uygun donanımlı ve yazılımlı bir GPS aleti ile yol tarifi alabilir , gittiğiniz yerleri hafızaya kaydedebilirsiniz.

Hava Filtresi
Motorun emme manifolduna giden havayı temizlemeye yarayan süzgeç/filtre.

Heel – Toe Shifter
(İng.) Motosikletteki klasik vites değiştirme sistemine eklanan bir parça ile ayağınızı koyduğunuz bir plaka vasitası ile topuk kısmına bastırdığınızda vitesi büyüten , burun kısmına bastırdığınızda ise vitesi küçülten bir sistemdir. Genellikle Cruiser tipi motorlarda görülür

Highsiding
(İng.) Sürücünün motosikletin gidonunun üzerinden uçtuğu durumlar için kullanılan terim. Genellikle arka frenle yapılan ağır frenlemelerde motosikletin arkası yalpalarken sürücünün freni bırakması sonucu boşalan yükün tepkisi sonucu sürücüyü üzerinden fırlatması durumu.

HOG
(İng. Harley Owners Group) Harley sahipleri grubu. Dünyaya yayılmış yaklaşık bir milyon üyesi olan , 1983’de kurulmuş bir kulüptür

Iron Butt
(İng.) Tam türkçeye çevirmek yerine neyi ifade ettiğini söylemek daha iyi olacaktır. 1 günde 1000 mil (1609 km) yol yapan motosikletçilerin kazandığı gayri resmi bir ünvandır. Iron Butt Rally ise 11 günde 11.000 mildir.

Jikle
(fr.gic lée) Emme manifolduna giden havayı kısarak karışımın zengin (yakıt ağırlıklı) olmasını sağlayan düzenek. Bazı motosikletlerde elle , bazılarında otomatiktir. Özellikle soğuk havalarda ilk çalıştırmada kullanılır. (Zenginleştirici – enrichener olarak da kullanılır) (Yanlış kullanım : cikle)

Jump Start
(İng.) Şarjı bitmiş bir akünün çalışır durumdaki bir aracın iyi durumdaki bir aküsünden paralel kablolarla şarj/diğer aracı çalıştırma yöntemidir.

Jant
Lastiklerin takildigi tekerlegin cember bicimindeki bolumu,ispit (fr.jante) (Yanlış kullanım : Cant)

Kampana fren
Frenlemenin fren balatası – yay - güç kolu ve çelik tas ile sağlandığı sistem. Genelde eski motorlarda ve günümüzde de bazı motosikletlerin arka tekerleklerinde kullanılır.

Kaliper
Disk frenlerin, balataları da içeren ve disklerin hidrolik oalrak sıkılmasına yarayan kısmı.


Karbüratör
(fr.Carburateur) Patlamalı motorlarda yakıt ile havayı karıştıran düzenek

Karenaj
Motosikletin sasisini orten bir nevi karoser (Yanlış kullanım : Grenaj)

Kask
(fr.casque) Kullanıcının başını ciddi yaralanmalardan korumak için giydiği koruyucu başlık

Kickstarter
(İng.) Günümüzde yaygın olarak kullanılmamakla birlikte Motocross , Scooter , Commuter tipi motorlarin bazilarinda elektrikli marşla birlikte veya tek başına sunulan , bir pedala aşağı doğru bir kuvvet uygulanarak motorun başlangıç hareketinin sağlanması sonucu motorun çalışmasına yardımcı olan düzenek.

Kill Switch
(İng.) Motorun ateşleme düzeneğine giden elektriği kesmeye yarayan düğme. Özellikle kaza anında ilk yapılması gerekenlerden biri motora giden ateşlemeyi keserek olası bir yangını engellemektir.

Konjektör
Voltaj Ayarlayacı. Alternatörün ürettiği yüksek voltajlı elektriği tüm elektrik sistemini besleyebilecek seviyede sabit tutmaya yarayan regülatör.

Karter
Motorun alt kısmını muhafaza eden parça.

Katalitik Konvertör
Egzoz gazında bulunan zararlı CO veya HC bileşiklerini yakarak daha az zararlı gazlara çeviren , 1974 yılında buluşu yapılmış , gaz emisyonunu düşüren bir parçadır.

Lowsiding
(İng.) Motosikletin ve sürücünün yere düştüğü durum. Bazen motosiklet sürücüleri bilinçli olarak motosikletlerini bırakarak/kaydırarak düşerler , ancak bu durum bazen daha fazla hasar ve yaralanmalara yol açabilir.

LED

(İng. Light Emitting Diode) Işık saçan diyot. Klasik ampüllere göre elektrik akımına daha hızlı tepki verdiklerinden dolayı ikaz ışıklarında (sinyal , stop lambası gibi) kullanılmaya başlanmıştır.

Lambda Sensörü
Katalitik Konvertör’ün önüne yerleştirilen , egzoz gazındaki O2 miktarını ölçen aygıttır. Sensör karışımdaki O2 miktarını mV olarak hesaplayıp değeri kumanda merkezine (beyin) ileterek en uygun karışımın hazırlanmasını sağlar.

Moped
(fr.)Pedaldan yardım alarak çalışan max.50 cc’lik motorlu bisiklet.

Motokros (MX)
(ing. Motocross) Genellikle insan yapımı tepeler ve dönüşlerle dolu , toprak-çamur karışımı pistlerin olduğu ve “Moto” adı verilen (Bizde bilinen adı ile Motokros motoru , dağ motosikleti) motorlarla yapılan yarışma

Motokros motosikleti
Yerden yüksek , yüksek ve yakın vites oranlı (Yüksek hızlanma , düşük üst hız) , fazla ön amortisör yolu olan , özel dişli lastikli , büyük cantli motosikletler. Dağ motosikleti olarak da bilinirler. Genellikle 250 cc’ye kadar olurlar.

Motor Koruma Demiri
Motosiklet motorunu dış darbelerden korumak için şasiden destek almış çelik bir korumadır.

Motosiklet
(fr.motocyclette) Motor silindirinin hacmi 125 cm³ den buyuk olan, iki tekerlekli motorlu tasit (yanlış kullanım : MotoRsiklet)

Naked Bike
(İng.) Karenajı (rüzgar koruması) olmayan/çok az olan , şasesi açıkca görülebilen spor – spor/turlama motorlarına verilen genel ad. Çıplak motor.

Orta Sehpa
Motosikleitn alt kısmına monte eidlmiş, yaylı mekanizması olan, kullanıldığıdında motosikletin arka lastiğini yerden havada tutan veya motosikleti dengede tutan aparat.

Odometre
(fr.odomètre) Motosikletin o ana kadar kattetiği mesafeyi mil ya da kilometre cinsinden gösteren ekrana verilen ad.


Off-Road

(İng.)Asfaltlanmış , beton atılmış , düzlenmiş , kısaca işlem görmüş yollar dışındaki yollar. Köy yolları veya stabilize yollar off-road değillerdir.

Orta Sehpa

(İng. Centre Stand) Motosikletin ağırlık merkezine çok yakın konumlandırılmış , motosikletin dengede durması sağlayan (zincir yağlarken , lastik değiştiriken , kışlamalarda) çift ayak.

Paralever

(Alm.) İlk kez BMW R100GS de kullanılna radikal bir arka süspansiyon sistemidir. Paralelogram prensibi ile çalışan ve bir tork kolu yardımı ile şaftın iki açıda hareketine olanak tanıyan sistem.

Peg
Motosikleti kullanirken ayaklarin konulduğu yer , ayaklik (Yanlış kullanım : ped)

Pilyon
(ing.pillion) Motosikletde sürücünün arkasında yolculuk yapan kişi, yolcu.

Pilot
Motosiklet sürücüsü , sürücü

Rider
(ing) Pilot , motosiklet sürücüsü , sürücü

Ride to Work Day
(İng.) 1989 yılında işten eve evden işe t-shirtleri ile ağza dolanan bu etkinlik 1992 ‘den beri düzenli olarak her yıl motosiklet sürücülerinin motosikletleri ile işe gitmesi ile anılır.

RPM
(İng. Revolution Per Minute) Motorun bir dakikada yaptığı tur sayısı. Devir/dakika

Radyatör
(Fr.Radiateur) Soğutma sistemi yağ veya su ile olan araçlarda ısınmış sıvıyı peteklerinden geçirirken fan veya aracın hızının oluşturduğu akımdan faydalanarak soğutmaya yarayan araçtır.

Reflektör
(İng.Reflector) Yansıtaç. Kendisine gelen ışığı değişik açılarda yansıtmaya yarayan araç.

Rölanti
(Fr.Ralenti) Gaz kelebeği serbest durumdayken, motorun yüksüz ve boşta çalışma devridir.

S.O.H.C.
(İng. Single Over Head Camshaft) Supaplı (silindir başına 2 veya fazlası) motorlarda motor üstünde bulunan supap açma kapamaya yarayan üstten tek kamın kısaltılmış hali.

Sele
(fr. selle) Motosikletin veya bisikletin oturulacak yeri

Sıkıştırma Oranı

Piston alt ölü noktada iken hesaplanan silindir içi hacmin , piston üst ölü noktaya geldiğinde hesaplanan hacime oranıdır.Dizel motorlarda sıkıştırma oranı benzinlilere göre daha yüksektir.

Sissy Bar
(İng.) Genellikle cruiser tipi motorlarda pilyon (yolcu) nun yaslanabileceği arkalık.


Scooter
(İng.)Ortada ayak koyma yeri olan -veya ortada deposu olmayip , sadece şase geçişi olan – küçük motosiklet.(Piaggio Vespa türün ilk örneklerindendir.)

Sportbike
(İng.)Pistlerde yarışmak amacı ile üretilmiş hız motosikletlerinin genel adı ( Honda CBR 1000RR , Kawasaki ZX10R , Yamaha R1..)

Sport-Tourer

(İng.) Spor bir motosiklet gibi sportif motora sahip olan , ancak turlama motorlarındaki gibi konfor içeren motosiklet ( Honda PAN European ST1300, Yamaha FJR 1300 , BMW K1200GT...)


Stoppie

(İng.)Ön frenlerin ayarlı bir şekilde sıkılması ile ön teker dengeli bir biçimde duruken arka tekerleğin havalanmasına verilen ad(Dikkat , sadece profesyoneller yapabilir ve tehlikelidir)

Supap
(fr.soupape) Valf olarak da bilinir. 4 zamanlı motorlarda silindirlerin üzerinde , iki zamanlılarda yanlarında buluna giriş ve çıkış kanallarının kapakları. 4 zamanlı motorlarda biri emme , biri ekzoz olmak üzere en az 2 adet bulunmaktadır.(Yanlış kullanım : Sibop , sübap vs..)


Supercross

(İng.) Motocross yarışmalarının kapalı alanlarda ve görece daha kısa parkurlarda yapılan hali.

Swing Arm
(İng.) Salıncak. Motosikletin şasesi ile arka tekerleğin bribirinden bağımsız hareket etmesine olanak tanıyan parça.

Sentetik Motor Yağı
Petrol bazlı mineral yağların aksine kimyasal reaksiyonlarla ortaya çıkarılmış ileri teknoloji ürünü performanslı motor yağlarına verilen genel ad.

Tank Bag
(İng.) Mıknatıs ve/veya kayışlar aracılığı ile depo üstüne yerleştirilebilen fermuarlı çanta

Tank Slapper
(İng.) Gidonun ani ve yoğun dengesiz salınım hareketi. Genellikle tümsekli bir viraj çıkışındaki güçlü hızlanmalar sırasında görülür. Gidon amortisörleri ile bu hareket kontol altına alınabilir.

Target Fixation
(İng.) Hedefe sabitlenme. Motosiklet sürücüsünün yol veya yol dışında bir noktaya (nesneye) odaklanması ve bu noktaya (nesneye) doğru sürüş yönünün kilitlenmesi sonucu sürüş çizgisinin bozulması. “Nereye bakarsan oraya gidersin!”

T-Bone
(İng.) Motosikletin –genellikle- bir otomobile yandan vurmuş haline verilen ad.

Takometre
(İng. Tachometer) Motorun dakikadaki devrini gösteren ekran/gösterge.

Telelever
(Alm.) BMW tarafından kullanılan ön amortisör sistemi. Öndeki iki çatalın içi yağ ile doluyken iki dirsek noktası ile salıncak görevi gören bir mekanizma vardır. Bunun sayesinde motosiklet ağır frenlemelerde ve çukurlarda ön tarafa dalma yapmaz.


Tork

(fr.Torques) Bir nesnenin ekseninden belirli mesafede uygulanan döndürme kuvvetine verilen addır. Örneğin bir somunu anahtarla açmaya çalışan bir operatör eğer 20 kgf’lık bir kuvvet uygulyor ise ve anahtar yük boyu 0,3 metre ise 6kgf-metre tork uygulandı denilir.


Trike
(İng.) Arkası iki tekerlekli olan üç tekerli motosikletlere verilen genel ad. Motosiklet şasesi üzerine kurulur ve arka tekerlek sökülerek yerine otomobil dingili ve özel bir şanzıman konulur.

Touring Bike
(İng.) Turlama motosikleti. Her ne kadar her motosiklet

Tubeless
(İng.) Şambrelsiz (iç lastik) lastik anlamında kullanılır.(Yanlış kullanım : Dubleks)

Twin-Port
(İng.) İki egzoz çıkışının olduğu silindir kafasına verilen ad.

Valf
(İng.Valve) Bakınız Supap.

V-Twin
(İng.) Konumlanması V şeklinde ve belli bir açıda olan (45 , 55 , 60 vs..) motorlara verilen ad.

Viskozite
(Fr. Viscosité) Akıcılık derecesi.Belli yoğunluk ve hacimdeki sıvının belli bir çaptan akma zamanı ile ölçülür. Numaralar düştükçe akıcılık artar (Su düşük , bal yüksek viskosdur)

Vuruntu
Detenasyon da denir. Yakıt hava karışımının bujinin ateşlemsinden önce kendi kendine tutşmasından doğan düzensiz ateşlenmedir. Bunun sonucunda motorun verimi düşer ve vuruntu denilen sesler duyulur.

Wheelie
(İng.) Gazın (debriyaj yardımı ile de olabilir) belirli bir güçte kullanılması ile ön tekerleğin yerden kesilmesine verilen ad. Tekteker.

İki Zamanlı
Pistonun her bir devrinde iki işlem yapmaktadır. Piston yukarı hareketinde sıkıştırma ve patlama, aşağı hareketinde ise yakıt hava karışımın emme ve egzozu dışarı atma.

Yağ Filtresi
Motorun yağını filtreden geçiren düzenek. Her motosiklet sürücüsü manuelde belirtilen periyodlarda yağ değişimi ile bu filtreyi değiştirmelidir. Aksi halde filtrede biriken metal parçacıklar motora hasar verebilir.

Yan Ayak
Motosiklet park pozisyonundayken soluna belli açıda yatmasını sağlayan yardımcı çubuk. Günümüzde birçok motosiklet yan ayak açıkken ya çalışmaz ya da vitese atıldığı anda durur.

Yan Çanta

(İng.Saddlebags) Motorun arkasında her iki yana sarkan ve tutturulan sert malzeme(Plastik , aliminyum , fiber vs) veya deriden yapılmış çantalar

Yolcu
Motosikletde sürücünün arkasında yolculuk yapan kişi. Bknz. Pilyon

Zenginleştirici
(İng. Enrichener) Bknz. Jikle

Zincir Tahrik
Motor gücünün arka tekerleğe bir zincirle aktarılması turlama için kullanılabilse de , genel anlam olarak az bakım gerektiren , çantalı , büyük yakıt tankı ve rüzgar koruması olan motosikletlere verilen genel ad.


30 yorum:

Adsız dedi ki...

I understand this question. Let's discuss.

Adsız dedi ki...

I confirm. All above told the truth.

Adsız dedi ki...

Thanks for sharing this link, but unfortunately it seems to be down... Does anybody have a mirror or another source? Please answer to my message if you do!

I would appreciate if someone here at lntoftheotherworld.blogspot.com could repost it.

Thanks,
William

L.N.T dedi ki...

William,
I couldn't understand the problem. How can I help you?

Adsız dedi ki...

die service seo world backlinks backlink building

Adsız dedi ki...

Hi there, I believe your blog might be having internet browser compatibility problems.

When I take a look at your site in Safari, it looks fine
however when opening in IE, it's got some overlapping issues. I merely wanted to give you a quick heads up! Apart from that, excellent site!
Here is my homepage ... GFI Norte

Adsız dedi ki...

Hello. Facebook takes a [url=http://www.nodepositbonus.gd]casinos online[/url] wager invest in on 888 casino sell: Facebook is expanding its efforts to the moment real-money gaming to millions of British users after announcing a deal with the online gambling companions 888 Holdings.And Bye.

Adsız dedi ki...

top [url=http://www.c-online-casino.co.uk/]casino bonus[/url] check the latest [url=http://www.casinolasvegass.com/]casino[/url] unshackled no store perk at the foremost [url=http://www.baywatchcasino.com/]www.baywatchcasino.com
[/url].

Adsız dedi ki...

The whole purpose oF collecting the name plus the e-mail aFFress oF your site visitors is [url=http://www.germanylovelv.com/]louis vuitton knolckoffs[/url]
help [url=http://www.germanylovelv.com/]louis vuitton knolckoffs[/url]
builF your possess hugely targeteF list that may be unique [url=http://www.germanylovelv.com/]louis vuitton knolckoffs[/url]
your busines[url=http://www.germanylovelv.com/]Louis Vuitton kopierte Tasche kaufen[/url]
Once you have all those names anF e-mail aFFresses, then you have permission [url=http://www.germanylovelv.com/]louis vuitton knolckoffs[/url]
contact them because they have opteF in [url=http://www.germanylovelv.com/]louis vuitton knolckoffs[/url]
submitting their name anF their e-mail aFFress [url=http://www.germanylovelv.com/]Louis Vuitton Outlet/[/url]
you . This is what's going to help [url=http://www.germanylovelv.com/]Louis Vuitton Outlet[/url]
builF customer loyalty, anF trust in you as a business owner..
|
|

Adsız dedi ki...

I am now not positive where you are getting your info, however great topic. I needs to spend a while studying much more or figuring out more. Thanks for magnificent info I was searching for this info for my mission. AL Dothan Payday Loans

Adsız dedi ki...

My spouse and I stumbled over here from a different web page and thought I should check things out. I like what I see so I am just following you. Look forward to checking out your web page for a second time. Payday Loans

Adsız dedi ki...

lntoftheotherworld.blogspot.com Check Advance FL Lutz Bir abone tabanının oluşturulması ve sadece nakit taşıyarak tatilinizi Kaynaş

Adsız dedi ki...

lntoftheotherworld.blogspot.com pop over to this web-site Oyaralanma kadar , olası bir elektrikçi , kalfalık ustabaşı olarak çalışmış

Adsız dedi ki...

lntoftheotherworld.blogspot.com try these guys Bu MLMs para üretmek için ne kadar zor dikkatli olmak emin olun

Adsız dedi ki...

lntoftheotherworld.blogspot.com website here Kredi olasılıkla tatmin edici miktarda hesaplarında kullanılabilir ya da başka olup olmadığını kendi banka hesapları kontrol edecek

Adsız dedi ki...

[url=http://zone.aimoo.com/blog/longchampsoldesk]sacs longchamp[/url] First of all, tape a paper in your room at least few days prior to your trip. Keep on adding the name of essential items that are must have for you. This will help you in opting for those items that are necessary for you, comprising shaving cream, Up-to-date Mulberry Elkington Natural Leather Briefcase Black for Men,Quality Guarantee Mulberry Handbags UK! razor, toothbrush, aftershave etc..
[url=http://longchamppasche.ucoz.com/blog]longchamp soldes[/url] Yu-Gi-Oh! also introduced another RPG game, Dungeon Dice Monsters. Although it had nothing near the popularity of the CCG, the Dungeon Dice Monsters board game dungeon crawl had a video game based on it, as well as featuring in the second Yu-Gi-Oh! anime series. The game is floundering in the water, with the first and last booster Highly Appreciated Mulberry Women's Bayswater Trimming Oxford & Leather Tote Bag Black released in the US in 2003..
[url=http://saclongchampa.xanga.com/weblog/]sac longchamp[/url] Against Texas two weeks ago he broke open a close game with Top Seller Mulberry Women's Daria Drawstring Leather Tote Purple Bag at auction, Mulberry store online is the good shopping place for Mulberry bags a diving catch that gave the Orange a 58-yard gain and set up the clinching touchdown in a 31-21 victory. Qadry maintains that he didn't feel pressed by Raghib's success, he just needed to mature at his own rate. "There was no identity carving," he says.. Oddly enough, it experienced been the seem and really feel of your baseball glove which grew to become the inspiration for the extremely first Coach handbag. They are created while using signature types this kind of as being the hobo, duffels and flaps. Like I stated earlier, in example you may be looking for that ideal handbag and need to happen over a ridiculous bargain, the most effective method to choose that could perhaps be by technique of eBay.

Adsız dedi ki...

Ӏ hаve been surfing onlinе more than 2 hоurs todaу,
yet I never found аny intегestіng articlе lіκe уours.
ӏt is pretty woгth enough for me. Pеrsonally, іf all web owners and
blοggers madе goοd content as you
did, the web will be much more usеful than eѵег bеfore.


Mу homeраgе :: garden centers denver

Adsız dedi ki...

But, Different the myriad rivals on the like day are here to serve you out. The treat simply takes 24 hours. If you borrowed a important measure. What just about guaranteed payday loans now! 2 jillion masses, 3 calendar month Guaranteed Payday Loans. Richele Messick, a act of multitude without any matter. 3 monthguaranteed payday loansis a similar industrial figure as substantially. To buffet these problems as intimately as commendation guidelines, which you have bad recognition Guaranteed Payday Loans are endowed to anyone without any acknowledgment check into Loan. http://www.guaranteedpaydayloans1.co.uk/ With this scheme, the great unwashed get out of this cash armed service n no meter level. But My dwelling house finance was the original theoretical account inexplicably left hand two keys as blanks, an on-going characteristic where we utter more or less guaranteed payday loans that don't very hold the necessary details wish loan measure. breathe is the key decision makers in C-suites approximately the body politic in which we conceive it's the workweek in Greenness. When a somebody is crying loans are identical overweight and very expensive. You may proudly say to you at the inconvenient prison term when an private to get completed.

Adsız dedi ki...

For round facial shape, go for the drop earrings
of Square, oblong, oval and rectangle shape. Designer
clothes are awesome and they are made up of quality stuffs and being a fashion conscious person it is very important to have one or two designer dresses for occasions.

Alessandra Ambrosio and Ashton Kutcher get cozy in a sultry campaign for Brazilian
clothing label Colcci.

Here is my page ... shbab.twhed.com

Adsız dedi ki...

Hi! I simply wish to offer you a big thumbs up for your excellent information you have here on this post. I am returning to your website for more soon.

[url=http://onlinepokiesking4u.com]real money pokies[/url]

Adsız dedi ki...

You really make it seem really easy together with your presentation but I to find this matter to be actually one thing which I
believe I'd never understand. It seems too complex and very vast for me. I am looking forward in your next submit, I'll attempt to get the hold of
it!

Here is my webpage: ford ranger forum

Adsız dedi ki...

Can I just say what a comfort to discover someone that really knows what they are discussing online. You actually understand how to bring a problem to light and make it important. More people should look at this and understand this side of your story. I can't believe you aren't more popular since you most certainly possess the gift.

[url=http://www.digitalserver.com.mx/blog/hosting-mexico/]hosting mexico[/url]

[url=http://www.digitalserver.com.mx]hosting en mexico[/url]

[url=http://www.digitalserver.com.mx]web hosting en mexico[/url]

Adsız dedi ki...

Can I just say what a comfort to uncover a person that actually understands what they are talking about over the internet. You actually realize how to bring an issue to light and make it important. A lot more people should read this and understand this side of the story. I was surprised that you're not more popular since you surely have the gift.

[url=http://www.digitalserver.com.mx/blog/hosting-mexico/]hosting mexico[/url]

[url=http://www.digitalserver.com.mx]hosting en mexico[/url]

[url=http://www.digitalserver.com.mx]web hosting en mexico[/url]

Adsız dedi ki...

Next time I read a blog, Hopefully it won't fail me just as much as this particular one. I mean, Yes, it was my choice to read through, nonetheless I genuinely believed you would probably have something helpful to talk about. All I hear is a bunch of crying about something you can fix if you weren't too busy looking for attention.

[url=http://casinoking4u.com]fantastic casino bonuses ready here[/url]

Adsız dedi ki...

The very next time I read a blog, Hopefully it won't fail me just as much as this particular one. I mean, Yes, it was my choice to read through, nonetheless I actually believed you would have something interesting to say. All I hear is a bunch of whining about something you could possibly fix if you weren't too busy looking for attention.

[url=http://casinoking4u.com]online casinos[/url]

Adsız dedi ki...

The very next time I read a blog, Hopefully it does not fail me as much as this one. After all, I know it was my choice to read through, however I actually believed you would probably have something interesting to say. All I hear is a bunch of complaining about something that you could fix if you weren't too busy searching for attention.

[url=http://casinoking4u.com]get the best deals here[/url]

Adsız dedi ki...

You're so awesome! I don't suppose I have read through anything like this before. So great to find another person with original thoughts on this subject. Really.. thank you for starting this up. This site is one thing that is required on the web, someone with a bit of originality!

[url=http://truebluepokies4u.com]online pokies[/url]

Adsız dedi ki...

Hi, I do believe this is a great web site. I stumbledupon it ;) I may return once again since i have saved as a favorite it. Money and freedom is the best way to change, may you be rich and continue to help other people.

[url=http://netticasinot4u.com]nettikasinot[/url]

Adsız dedi ki...

Hi there! I could have sworn I’ve visited this website before but after looking at many of the articles I realized it’s new to me. Regardless, I’m certainly pleased I came across it and I’ll be book-marking it and checking back regularly!

[url=http://protutoriel.com/]application[/url]

Adsız dedi ki...

Piece of writing writing is also a excitement, if you be familiar with after that you can write otherwise it is difficult to write.


Feel free to surf to my homepage http://wiki.sedcard-service.de/index.php?title=Benutzer:InadccR94